Dolomite Slate    (Length 1000mm: Width 160mm: Thickness 20mm)
 

Dolomite Dark    (Length 1000mm: Width 160mm: Thickness 20mm)

Dolomite Grey    (Length 1000mm: Width 160mm: Thickness 20mm)

Dolomite Mars Rust  (Length 1000mm: Width 160mm: Thickness 20mm)

Dolomite Moon    (Length 1000mm: Width 160mm: Thickness 20mm)

Dolomite Sunset    (Length 1000mm: Width 160mm: Thickness 20mm)

Dolomite Dust    (Length 1000mm: Width 160mm: Thickness 20mm)

Dolomite White    (Length 1000mm: Width 160mm: Thickness 20mm)

Dolomite French Limestone (Length 1000mm: Width 160mm: Thickness 20mm)

Dolomite Travertine  (Length 1000mm: Width 160mm: Thickness 20mm)

All dimensions are nominal.
 

Specification
 

Coverage
 

1000mm x 160mm

1 plank to a linear metre (Edging)

6.2 planks approximatly 1m²

Laying Instructions

Download Laying Instructions 

Laying Comments

Porcelain Plank paving tiles are rectified to give a calibrated, dimensional accuracy. This enables closer jointing so that the tiles can appear as one large uninterrupted, seamless surface of stone flooring.

A rectified floor tile is one whose edges are perfectly vertical with respect to it's surface. This is a result of precise machining of a regular unrectified tile, so that each of the four sides will be at a 90° angle to the top and bottom faces of the tile.

Lay on an MOT Type 1 or GSB aggregate sub-base, over a geo-textile covering.

Set the paving tiles on a full wet mortar bed (40mm), using a 5:1 sharp sand : cement ratio.

Cut tiles with a 'Diamond Porcelain Cutting Blade' (circular no teeth) on a hand tool  or table saw.  Use 'water dust suppression'.

It is essential to use a Priming Slurry, which should be applied to the underside of each paving tile just prior to laying.

Joint width ideally 5mm (optimum cosmetically).

Porcelain is manufactured in batches and the the colour and texture can vary from batch to batch. It is therefore essential to lay the paving by mixing the tiles from each of the packs that are to be laid. This ensures that the overall desired hue is achieved and evens out any slight colour discrepancies. Laying your patio one pallet at a time can lead to slight but visible colour banding.

Keep a note of the 'batch code' of the porcelain being laid in case you need more to complete or extend your paved area. This can be found on the packaging (usually a number followed by a letter, or a six digit number.

A flexible jointing grout should be used to joint the tiles and care must be taken not to let it dry on the surface of the tile.

Please refer to our laying instructions if in any doubt.

Keep your paving looking superb, year after year!

A range of scientifically advanced cleaning products that will clean and help maintain all types of natural stone, concrete and porcelain paving.

	PATIO CLEANER A heavy duty cleaner for removing stubborn ground in dirt and grime from patio and pathway paving. Suitable for sandstone, limestone, travertine, slate, granite, marble, terracotta, brick, concrete and porcelain patio paving. Available: 1ltr, 5ltr
Technical Data Sheet	Application Guide
	BLACK SPOT & ALGAE REMOVER Removes black spot, lichen, moss and stains from natural stone, concrete and porcelain patio and pathway paving. Suitable for sandstone, limestone, travertine, slate, granite, marble, terracotta, brick, concrete and porcelain patio paving. Available: 5ltr
Technical Data Sheet	Application Guide
	DRIVEWAY CLEANER   Removes engine oil, air-con fluids,  tyre marks and other vehicle stains and rubber deposits, in addition to removing vegetation staining from driveway concrete block paving and natural stone block paving. Available: 5ltr
Technical Data Sheet