Natural Stone Porcelain
Natural Stone Porcelain
Reproducing some of the most popular natural stone pavings available, The Pavestone 'Natural' Porcelain range has an exceptional and convincing look and feel to the Granite, Sandstone and Yorkstone reproductions.
Almost indistinguishable from natural stone, however porcelain comes without the need for constant cleaning and sealing attributed to natural stone paving.
'Natural' porcelain tiles can be profiled with a choice of edge profiles for making steps or smooth edges for raised patios.
See Pavestone Bespoke.
Natural Greystone Porcelain
Specification
Size* | 900mm x 600mm (Rectified) |
Tolerance | +/- 1mm |
Finish | Stone effect; Textured |
Edge Profile | Square edge. Bullnose edge available |
Slip Resistance | >R11 |
Frost Resistant | Yes |
Water Absorption | <0.01% |
Coverage
(Silver & Black Granite & Greystone)
40 paving tiles per pallet.
Available as single paving tiles.
1.9 paving tiles covers approximately 1.0m2
40 paving tiles (1 pallet) covers approximately 21.6m2
Coverage
(YORKSTONE)
48 paving tiles per pallet.
Available as single paving tiles.
1.9 paving tiles covers approximately 1.0m2
48 paving tiles (1 pallet) covers approximately 26.0m2
Key features
- R11Anti-slip Finish**
- Natural porcelain paving tiles will not be affected by the seasonal weather changes and will not deteriorate in freezing weather conditions that can see some stone surfaces deteriorate gradually.
- Natural porcelain paving tiles are resistant to acid and alkali chemicals such as fertilizers and lawn treatments. Moss and algae cannot get established as they can on stone.
- Natural porcelain paving tiles will not experience colour fading. Blacks will stay black, not turn to grey, light colours will stay faithful and will not turn grey/brown. In summary they will stay looking aesthetically as laid for many years with minimal cleaning maintenance.
NOTES
* With 'Rectified' porcelain paving the dimensional variation between the size of individual paving slabs, within a batch, is much less than that of a non-rectified tile. This is because it is cut to size after the tile has been fired (baked) in the kiln. Typical variance +/- 2mm.
The actual tile dimensions are 'nominal' and may be less than the stated nominal measurements by up to 5mm. However, in each batch the variation between tiles will only be +/-2mm. When tiling you should always use tiles from the same production batch.
Always check the batch number on the packaging when laying porcelain paving as this will ensure the variation in sizes between the slabs is minimal.
** R11 Anti-slip Finish is the latest development to meet the growing demand for porcelain outdoor paving. This unique finish roughens the tile surface without changing its appearance giving good grip underfoot in damp and wet weather.
Laying Instructions
Download Laying Instructions
Laying Comments
Lay on an MOT Type 1 or GSB aggregate sub-base, over a geo-textile covering.
Set the paving tiles on a full wet mortar bed (40mm), using a 5:1 sharp sand : cement ratio.
Cut tiles with a 'Diamond Porcelain Cutting Blade' (circular no teeth) on a hand tool or table saw. Use 'water dust suppression'.
It is essential to use a Priming Slurry, which should be applied to the underside of each paving tile just prior to laying.
Joint width ideally 5mm (optimum cosmetically).
Porcelain is manufactured in batches and the colour and texture can vary from batch to batch. It is therefore essential to lay the paving by mixing the tiles from each of the packs that are to be laid. This ensures that the overall desired hue is achieved and evens out any slight colour discrepancies. Laying your patio one pallet at a time can lead to slight but visible colour banding.
Keep a note of the 'batch code' of the porcelain being laid in case you need more to complete or extend your paved area. This can be found on the packaging (usually a number followed by a letter, or a six digit number).
A flexible jointing grout should be used to joint the tiles and care must be taken not to let it dry on the surface of the tile.
Please refer to our laying instructions if in any doubt.
Keep your paving looking superb, year after year!
A range of scientifically advanced cleaning products that will clean and help maintain all types of natural stone, concrete and porcelain paving.
PATIO CLEANER
Suitable for sandstone, limestone, travertine, slate, granite, marble, terracotta, brick, concrete and porcelain patio paving. Available: 1ltr, 5ltr
|
|
Technical Data Sheet | Application Guide |
BLACK SPOT & ALGAE REMOVER
Suitable for sandstone, limestone, travertine, slate, granite, marble, terracotta, brick, concrete and porcelain patio paving. Available: 5ltr
|
|
Technical Data Sheet | Application Guide |
DRIVEWAY CLEANER
Removes engine oil, air-con fluids, tyre marks and other vehicle stains and rubber deposits, in addition to removing vegetation staining from driveway concrete block paving and natural stone block paving. Available: 5ltr
|
|
Technical Data Sheet |
Contact Us
To find out more about Natural Stone Porcelain, you can call us or email us.
01386 848 650 enquiries@pavestone.co.ukFind a Landscaper
To find your nearest preferred landscaper, please enter your postcode below.
Bespoke
Cutting & Profile
Introducing our new bespoke porcelain cutting and profiling service.
Find out more