Lecco Gris (900 x 600 x 20mm)

Lecco Grafito (900 x 600 x 20mm)

Lecco Crema (900 x 600 x 20mm)

Specification

Coverage

42 paving tiles per pallet.

1.85 paving tiles cover approximately 1.0m²

42 paving tiles (1 pallet) cover approximately 23m² based on a 5mm jointing gap.

Key features

• R11anti-slip finish**
   
• Lecco porcelain paving tiles will not be affected by the seasonal weather changes and will not deteriorate in freezing weather conditions that can see some stone surfaces deteriorate gradually.
   
• Lecco porcelain patio tiles are resistant to acid and alkali chemicals such as fertilizers and lawn treatments. Moss and algae cannot get established as they can on stone.
   
• Lecco porcelain paving tiles will not experience colour fading. Blacks will stay black, not turn to grey, light colours will stay faithful and will not turn grey/brown. In summary they will stay looking aesthetically as laid for many years with minimal cleaning maintenance.

• Lecco porcelain tiles are rectified* to give a calibrated, dimensional accuracy. This enables closer jointing so that the tiles appear as one large uninterrupted, seamless surface of flooring.
   

NOTES

*  With 'Rectified' porcelain paving the dimensional variation between the size of individual paving slabs, within a batch, is much less than that of a non-rectified tile. This is because it is cut to size after the tile has been fired (baked) in the kiln. Typical variance  +/- 2mm.

The actual tile dimensions are 'nominal' and may be less than the stated nominal measurements by up to 5mm. However, in each batch the variation between tiles will only be +/-2mm. When tiling you should always use tiles from the same production batch.

Always check the batch number on the packaging when laying porcelain paving as this will ensure the variation in sizes between the slabs is minimal. 

** R11 Anti-slip Finish is the latest development to meet the growing demand for porcelain outdoor paving. This unique finish roughens the tile surface without changing its appearance giving good grip underfoot in damp and wet weather.

Laying Instructions

Download Laying Instructions 

Laying Comments

Discovery porcelain patio paving tiles are rectified to give a calibrated, dimensional accuracy. This enables closer jointing so that the tiles can appear as one large uninterrupted, seamless surface of stone flooring.

A rectified floor tile is one whose edges are perfectly vertical with respect to it's surface. This is a result of precise machining of a regular unrectified tile, so that each of the four sides will be at a 90° angle to the top and bottom faces of the tile.

Lay on an MOT Type 1 or GSB aggregate sub-base, over a geo-textile covering.

Set the paving tiles on a full wet mortar bed (40mm), using a 5:1 sharp sand : cement ratio.

Cut tiles with a 'Diamond Porcelaing Cutting Blade' (circular no teeth) on a hand tool  or table saw.  Use 'water dust suppression'.

It is essential to use a Priming Slurry, which should be applied to the underside of each paving tile just prior to laying.

Joint width ideally 5mm (optimum cosmetically).

Porcelain is manufactured in batches and the colour and texture can vary from batch to batch. It is therefore essential to lay the paving by mixing the tiles from each of the packs that are to be laid. This ensures that the overall desired hue is achieved and evens out any slight colour discrepancies. Laying your patio one pallet at a time can lead to slight but visible colour banding.

Keep a note of the 'batch code' of the porcelain being laid in case you need more to complete or extend your paved area. This can be found on the packaging (usually a number followed by a letter, or a six digit number).

A flexible jointing grout should be used to joint the tiles and care must be taken not to let it dry on the surface of the tile.

Please refer to our laying instructions if in any doubt.

Keep your paving looking superb, year after year!

A range of scientifically advanced cleaning products that will clean and help maintain all types of natural stone, concrete and porcelain paving.

	PATIO CLEANER A heavy duty cleaner for removing stubborn ground in dirt and grime from patio and pathway paving. Suitable for sandstone, limestone, travertine, slate, granite, marble, terracota, brick, concrete and porcelain patio paving. Available: 1ltr, 5ltr
Technical Data Sheet	Application Guide
	BLACK SPOT & ALGAE REMOVER Removes black spot, lichen, moss and stains from natural stone, concrete and porcelain patio and pathway paving. Suitable for sandstone, limestone, travertine, slate, granite, marble, terracota, brick, concrete and porcelain patio paving. Available: 5ltr
Technical Data Sheet	Application Guide
	DRIVEWAY CLEANER   Removes engine oil, air-con fluids,  tyre marks and other vehicle stains and rubber deposits, in addition to removing vegitation staining from driveway concrete block paving and natural stone block paving. Available: 5ltr
Technical Data Sheet